Togetherness, inspiration and creativity

How To Make A Handmade Notebook – Julie Peasgood

How To Make A Handmade Notebook – Julie Peasgood

Compulsive list-maker and Crafty Beggar, Julie Peasgood, takes you through how to make your own notebook in this fantastic tutorial. A great gift idea for Mother’s Day, you could select a bold print fabric you know she’d love, and make it the perfect size to pop into her handbag for list-making on the go! Over to Julie, for step-by-step instructions on how to make your own notebook that’s bound to put you in her ‘good books’ this Mother’s Day!

I am a compulsive list maker, and I caught the habit from my dear mum, Pearl, who was always making lists on bits of paper or the backs of envelopes!

Sadly, my mum passed away many years ago now, but I think she would have loved making her lists in these little handmade books. They make a perfect Mother’s Day gift – and can be made from just a scrap of material… perfect for using up those leftovers!

Top Tip:

It’s easier if you use a darker material (they show less marks!) and preferably one that doesn’t fray.

You Will Need:

Step 1:

Lay out your materials, and place your fabric face side down. It should measure 13x8inches. The cardboard (for the book cover) measures 3ins by just under 4ins, and your spacer is also just under 4ins by 0.75ins. Your pages should be 3.5 ins by 3ins.

Step 2:

The secret to making a successful book is to use as little glue as possible – you apply it and then you scrape nearly all of it off!  You do need to use bookbinding glue too – it might seem just the same as PVA glue, but it’s not. PVA is cheaper, but it contains a lot of water, so it can stain the material you’re using. Bookbinding glue may be a bit more expensive, but it has a drying agent built within it, so it’s stronger and won’t mark your material.

Step 3:

After laying everything out, take your pages and group them together. Next, apply a thick layer of bookbinding glue to the top edge (this is the ONLY time you use the bookbinding glue quite thickly!) Place the shirting on the top of the pages (measure a strip of it – 3.25ins) and press down to seal. Glue the sides down too, but wait until everything is dry to neaten it up and to chop off any stray edges.

Step 4:

At this point you could disguise the shirting with some material (so the shirting doesn’t show when the book is opened) but depending on your choice of material, it can sometimes make the book rather thick to close.

Step 5:

The next step is to position your cardboard pieces and the spacer on your material (which you have placed face side down). There doesn’t need to be lots of material around the edges of the cardboard; 0.25ins is enough to create a good overlap.

Step 6:

Glue both the thicker cardboard rectangles onto the material (but DON’T glue the spacer!) and turn them over to gently smooth out any creases.

Step 7:

Next, cut around each of the thin cardboard rectangles – again leaving 0.25ins all round. Cut the corners off (to avoid build-up of material) and as the corners are likely to be messy, just dab a tiny bit of glue on them (with your spatula) to smooth them back.

Step 8:

Now cut the two thicker cardboard pieces all together (the thinner cardboard pieces are cut separately, but the thicker cardboard forms the outside of the book and therefore needs to be all one piece). Cut the corners again and turn the material over the edges, and then glue on the thin cardboard pieces.

Step 9:

Glue the ribbon across the centre of the book (again face side down). Then take the pages and glue them where the spacer was – and hold the book together with the elastic band until it’s dry.

Step 10:

If desired, glue the first pages at the front and back to the inside cover to make it all look neat and tidy!

Looking for Mother’s Day ideas? Check out all our Mother’s Day projects right here on the blog!

Lisa at Create & Craft